How To Paint a Metal Door That Is Peeling?

How To Paint a Metal Door That Is Peeling

Have you tried to refurbish an old steel door on a shed or a garden gate that is no longer maintaining its coat of paint? Saponification is the source of the problem. Moisture has made its way beneath the primer over time, forming zinc oxide. The oils from new paint layers react with the oxide to generate a soap, which quickly deteriorates the paint film, causing the paint layer to loosen and break down. In this article, will introduce a step-by-step guide to let you know How To Paint a Metal Door That Is Peeling

How To Paint a Metal Door That Is Peeling

Paint a Metal Door That Is Peeling

The remedy is to remove the paint and revert to bare metal. Sand all of the rough, rusty edges down to reveal the gleaming metal beneath. Start by removing as much rust as possible using a wire brush from any rusty spots. To get a smooth and lustrous bare metal surface, start sanding with a coarse grit (80 to 120) sandpaper and work your way down to a finer grain (180 to 240).

Once your door or gate is free of rust and paint, it’s time to reassemble the layers. Begin with prep and etch product, which is essentially phosphoric acid that has been diluted. Allow it to dry for about half an hour after brushing it all over the exposed steel. Allow the door or gate to dry completely in a heated place or in the sun after rinsing it.

After the door has dried completely, prime it with a high-performance acrylic primer designed for surfaces with adhesion issues, such as vinyl, plastics, and galvanized metals. Make sure all of the fine edges, gaps, and grooves are primed. This is the most crucial step in ensuring a long-lasting finish on your newly renovated door. If you don’t have a spray gun, use a broad paintbrush for wide surface areas and a fine paintbrush for edges and fine detail work.

Finally, apply two coats of an excellent quality exterior acrylic topcoat to the door. Because there will likely still be very light remains of zinc oxide on the steel, the oils in the enamel paint will react with the oxide and the same problem will recur, you are now using an acrylic topcoat instead of enamel paint. The saponification reaction cannot occur when using water-based paint because the oils are removed from the painting.

Allow the paint to dry completely between coats, and your door will have a fresh, long-lasting paint finish.

Step-by-step to Do How To Paint a Metal Door That Is Peeling

1. Take out the door and all of the hardware.

Remove the door from its frame for the best effects. This isn’t essential, but it will help you reach the best potential result. Then take out all of your door’s hardware, including the letterbox, door handles, hinges (if the door has been removed from the frame), knockers, and so on. Painting around these elements in an inconvenient manner will slow you down. Tape over anything you don’t want to be painted if you can’t remove the hardware from your door. This will assure a clean finish.

2. Use a degreaser to clean the door.

Paint a Metal Door That Is Peeling 1

Make sure the surface is clean before applying the paint for a smooth finish. Using a degreaser and a rag, clean the surface of your door to remove any dirt, oil, grease, or grime.

After cleaning the door, wash it down with a dry cloth and set it aside for an hour or two before continuing.

3. Get rid of any old paint.

This phase will be determined by the state of your door. If the paint is flaky, you’ll need to remove it with a paint stripper or a heat gun. When removing the previous paint, avoid using an abrasive material to avoid damaging the metal. Because paint stripper generates fumes, make sure you do this step in a well-ventilated place if you’ve removed the door from the frame. If the door cannot be opened, ventilate the room as much as possible and wear respiratory and eye protection.

4. Sand the door down

After you’ve removed any old paint or if your door is already paint-free, sand it down to make it easier for the primer and paint to stick to the surface. Sand the door carefully and lightly with fine sandpaper while using a dust mask and safety glasses – 400-grit sandpaper is best.

To eliminate any dust left over the following sanding, give the surface a brisk wipe with a moist cloth.

5. Prime

Using a good primer will protect your door and provide a long-lasting barrier. The primer you select will be determined by the paint you intend to use on your door. If you plan on painting with latex or oil-based paint, this multi-surface primer will suffice.

You’ll need a paint roller for the main portions and an angled sash brush for the panels and corners to apply the priming. It will take one to three hours for the primer to dry, depending on the primer you select. Make careful to follow the manufacturer’s directions and, if necessary, add a second coat.

Before moving on to the next step, make sure your primer is totally dry.

6. Paint your canvas

Apply one coat of exterior paint to the flat areas of the door with your paint roller, and use your angular sash brush to any paneled areas or corners using your angular sash brush. Use an exterior satin or semi-gloss paint that is suitable for external use.

To maintain a consistent and long-lasting finish, use a minimum of two coats. Before applying another coat, make sure the previous one is totally dried. The manufacturer’s instructions will most likely specify how many coats you’ll need and how long each coat should be allowed to dry.

Work on one side of the door at a time if you’re painting both sides, as wet paint can be harmed if it comes into contact with another surface too rapidly. Allow at least 12 hours for your door to dry after you’ve finished painting it.

Paint a Metal Door That Is Peeling 2

7. Replace the door’s hardware and rehang it.

Remove any tape and reattach the hardware to your door once the paint has completely dried. If you took your door down, the last step is to reinstall it.

To paint a metal door, you’ll need the following supplies and tools.

  • Painter’s tape: Using painter’s tape will provide a crisp, clean line and a professional-looking paint job, as well as covering areas of the door that you don’t want to be painted.
  • Degreaser: This cleans your door of any grease or oil stains.
  • Paint stripper: Ensures a professional polish by removing paint, varnish, lacquer, and epoxy from metal.
  • Sandpaper: For a satin-smooth finish and good primer adhesion, use sandpaper.
  • Primer for multi-surface improves paint adhesion to surfaces, resulting in a longer-lasting finish.
  • Paint roller: Useful for painting huge expanses of metal doors.
    An angled sash brush helps you to paint precise corners, panels, and beveled edges with ease.
  • Acrylic satin paint on the outside resists scratches and scuff marks for a high-quality, long-lasting finish.
  • Semi-gloss paint: This oil-based composition provides a long-lasting protective layer that also resists rusting.

When should you hire a pro to paint a metal door?

Paint a Metal Door That Is Peeling 3

If you’re still not confident about painting a metal door yourself, you should hire an expert. The items indicated above are safe to use at home, but they are costly and require a lot of patience and a steady hand. If your metal door has a lead-based paint coat, it is strongly advised that you seek professional assistance. Lead-based paint must be removed and lead contamination avoided in a carefully regulated setting.

Using a professional will come at a price, so make sure it’s something you can afford. If you’ve never painted before, you’ll almost certainly get better results from a professional and in a shorter amount of time than if you did it yourself.

Most Commonly Asked Questions

Is it possible to paint a metal door?

Yes. This is a job you can undertake at home if you have the right tools and products. Remove the door from its frame, remove or tape off any hardware, then sand, prime, and paint it. With the correct instruments, it may be a rather simple job.

On a metal door, how long should I wait between applications of paint?

The time it takes for your paint to dry varies depending on the type of paint you use, but it usually takes one to three hours. For more information, consult the paint’s manufacturer’s instructions. Check the paint by softly touching it to make sure it’s entirely dry.

What is the best way to get rid of rust spots?

If the door is still structurally sound, sand the rust spots and treat them with a rust inhibitor before priming and painting the door as usual. If the rust has caused any holes or fractures in the door, it may be necessary to replace it totally.

Is it necessary to sand my door if it has already been painted, or can I just prime it?

You don’t need to sand the door if the paint isn’t flaky or peeling. However, prime it before repainting to ensure that the fresh paint layer adheres well.

What causes the paint on the door to flake after it has been painted?

If you don’t prepare your surface properly, you’ll end up with flaky paint. You must ensure that your paint bonds properly to the door’s surface in order for it to adhere well. This is accomplished by removing any grease, oil, or filth from the door, sanding it down, and then priming it before painting.

After a long time being used, your door needs to be repainted. Hope all the guides from can help you deeply know about How To Paint a Metal Door That Is Peeling

Previous articleHow To Fix Hard Water In House – Best Solution
Next articleWhy Does My Dryer Squeak? How to Fix a Squeaky Clothes Dryer


Please enter your comment!
Please enter your name here