How To Change Dryer Heating Element – Step-by-step Guide

How To Change Dryer Heating Element

The element is a coil of heating wire that warms up with an electric current. The hot coils heat the air blowing over the element before it enters the dryer drum. There’s a significant probability your dryer’s heating element is broken if it takes longer than usual to dry your clothing or the air entering the dryer drum never becomes hot. In this article, will introduce a step-by-step guide on How To Change Dryer Heating Element

Simply checking the coils of a heating element will often reveal whether it is the source of your non-heating dryer. A defective heating element is indicated by burns or breakage in the coils. You can use a multimeter to do a continuity test if you inspect the coils and notice no signs of damage. The test will determine if the element’s electrical channel passes through all of the coils without being interrupted. Your heating element is most likely to blame for your dryer’s malfunction and will need to be replaced if you have a broken electrical path.

how to change dryer heating element 1

Before to know How To Change Dryer Heating Element

  • Before you begin your repair, unplug your dryer or turn it off at the circuit breaker.
  • During an appliance repair, always use safety goggles and work gloves to protect your eyes and hands.
  • Stop what you’re doing and call an appliance repair specialist if you fear you won’t be able to finish repairing your dryer safely.

How To Change Dryer Heating Element

Remove the dryer from the outlet and place it in a large open area where you may work on it. Place the dryer on the floor on its front side. The heating element in most front-load dryers is located in the back of the dryer, but check your owner’s handbook to be sure.

Unscrew the back panel of the dryer, which normally includes 10 to 12 screws, with a screwdriver or nut driver. Remove the cover gently and lay it aside. The heating element should be positioned about a foot above the dryer’s bottom. The size of this square box will vary, but it will have coils within that resemble little springs.

how to change dryer heating element 1

Remove the two screws that secure the heating element. Disconnect the two wires, also known as electrical connections, that are connected to this box. You’ll need to label the wires so you know how to reconnect them.

Inspect the box for any loose or damaged springs on the interior. If they are, the heating element must be replaced.

A replacement heating element can be found at your local appliance store. Take the dryer’s serial number and manufacturer’s name with you.

Carefully place the replacement heating element in the dryer, making sure it does not fall out. Reconnect the two wires in the same way that you labeled them so that they fit perfectly in the old heating element. To ensure that the heating element does not shift, tighten the screws.

Tighten the screws and replace the back cover panel. Return the dryer to its original position against the wall. Turn on the dryer after plugging it in. You should have access to heat. Allow the dryer to run for a few minutes to allow the new heating element to settle in.

Is it difficult to replace the heating element in a dryer?

Thankfully, replacing a heating element isn’t a difficult task. A replacement heating element may generally be found at a local hardware shop or online by searching for your dryer model number. Unplug the dryer, remove the rear panel, disconnect the connections, and replace it with the new one.

Frequently Asked Questions

How much does a dryer heating element cost?

How Much Does a Dryer Heating Element Cost? A new heating element can cost anything from $40 to $100. Depending on the type of dryer, this item could cost anywhere from $30 to $200 or more.

How can you tell if your dryer’s heating element is broken?

Examine the metal wire coil for any wire breaks. The heating element should be fine if the wiring is firm and free of fractures. The heating element is defective if the wire has a break in it.

change dryer heating element 2

Is it simple to swap out a heating element?

In most electric ovens and ranges, an oven heating element is a basic component that may be easily replaced. A replacement oven element is available from the oven manufacturer or via internet appliance parts retailers.

What happens if you put damp items in the dryer?

Wring them out as much as you can, either by hand or in the washing machine, or let them drip until most of the water is gone, then finish drying them in the dryer. The purpose of a dryer is to dry moist clothing, not soaking wet ones.

Is it possible for me to repair my dryer on my own?

You don’t need any prior experience to handle most difficulties. With a few basic tools and a continuity tester or multimeter, you can solve most dryer problems in an hour, and you can do it yourself with these straightforward instructions.

Is it cheaper to repair or replace a dryer?

When it comes to any appliance, the usual rule is that if repair costs are more than half of the replacement cost, it’s time to replace it. You can get a basic dryer for under $300, but it won’t save you any money on energy because it isn’t Energy Star rated. It’s a toss-up whether to fix or replace in this situation.

What’s the deal with my dryer running but not heating up?

A tripped circuit breaker, clogged vent, or no gas flow are all common causes of an electric or gas dryer, not heating. A damaged thermal fuse or a broken heating element are two other possibilities.

How long does it take a dryer to wear out?

A dryer should last between ten and thirteen years. Clean the lint trap after each use to extend the life of the dryer, and ensure sure the exterior vent is clear as well.

How frequently do dryer heating elements fail?

The Bottom Line The heating element in a dryer can last between 8 and 18 years if it is well-maintained and the vents and lint traps are kept clean. The heating element in a dryer that is used on a daily basis and is not well-maintained can burn out at any time.

How long does the heating element in a dryer last?

If the dryer is well-maintained and the vent and lint traps are clean, the heating element can last between 8 and 18 years. If the dryer is not well-maintained, the heating element may burn out.

Does a dryer’s heating element glow?

A red glow can occasionally be observed inside the dryer drum. This is very normal. The glow is caused by the heating element, and it is most visible when the cycle has been halted to remove or add an item of clothing. The element turns off when the cycle draws to a close.

Is it necessary to drain the water heater in order to replace the element?

It is possible to replace the heating element in your water heater without draining the tank. However, keep in mind that it may be more difficult.

In most electric furnaces, what regulates the heating element?

The thermostat transmits an electric signal to relays inside the furnace, which initiates the healing process. Those relays provide voltage to the heating elements, which causes them to heat up. Following that, forced-air blowers are turned on to transport hot air through the cabinet, eventually heating the house’s living areas.

change dryer heating element 3

Are the heating elements on the top and bottom the same?

The majority of domestic electric water heaters contain two heating components, one near the top and one towards the bottom of the tank. When the water at the top of the tank becomes too hot, the top element switches off and the lower one begins to heat. The upper and lower heating components are never turned on simultaneously.

Is it possible to help by putting a towel in the dryer?

Throwing a dry towel in with wet garments in the dryer absorbs the majority of the moisture, allowing your clothes to dry faster. Putting a dry towel in the dryer with your clothing absorbs part of the moisture, allowing the items to dry faster.

Is it possible to dry wet towels in the dryer?

All objects going into your dryer should have been spun on high to extract as much water as possible. Wet blankets should be washed on the spin cycle to remove the majority of the water. Then you may put them in the dryer. Do not use the dryer to dry them.

Is it possible for a dryer to catch fire after it is turned off?

Is it possible for a dryer to catch fire even while it is turned off? After the dryer has been switched off, problems with the electrical system might cause wiring and components to short or spark. Lint accumulation can cause filters to overheat, burning the material long after the dryer has been turned off.

If your dryer is not heating, you should look into the heating element assembly. The heating element, the inlet control thermistor, or the safety thermostat–all of which are located on the heating element assembly–could be defective. Hope the following guides from will help you Change Dryer Heating Element successfully

Previous articleHow To Remove Rust From Chrome With Vinegar


Please enter your comment!
Please enter your name here